Metabolic Cost and Mechanical Efficiency of a Novel Handle-Based Device for Wheelchair Propulsion.

OBJECTIVE: To investigate differences in metabolic cost and gross mechanical efficiency of a novel handlebased wheelchair propulsion device and to compare its performance with conventional push-rim propulsion. DESIGN: Double-group comparative study between 2 different propulsion methods. PARTICIPANTS: Eight paraplegic individuals and 10 non-disabled persons. METHODS: Participants performed the same exercise using a push-rim device and the novel handle-based device on a wheelchair- based test rig. The exercise consisted of a combined submaximal and maximal test. Power output, oxygen uptake, ventilation, respiratory exchange ratio and heart rate were recorded continuously during the tests. Analysis of variance was performed to determine the effects of group, mode and on power output. RESULTS: Submaximal exercise resulted in a higher efficiency for the novel device and significant main effects of propulsion mode on all investigated parameters, except heart rate. On the respiratory exchange ratio, a significant interaction effect was found for both mode and group. The maximal exercise resulted in a higher peak power output and lower peak heart rate during propulsion using the handle-based device. A significant main effect on mode for mean peak power output, ventilation and heart rate was also observed. CONCLUSION: Wheelchair propulsion using the handle-based device resulted in lower physical responses and higher mechanical efficiency, suggesting that this novel design may be well suited for indoor use, thereby offering an attractive alternative to pushrim wheelchairs.

Non-parametric dynamical estimation of blood flow rate, pressure difference and viscosity for a miniaturized blood pump.

Blood pumps are becoming increasingly important for medical devices. They are used to assist and control the blood flow and blood pressure in the patient's body. To accurately control blood pumps, information about important hydrodynamic parameters such as blood flow rate, pressure difference and viscosity is needed. These parameters are difficult to measure online. Therefore, an accurate estimation of these parameters is crucial for the effective operation of implantable blood pumps. In this study, in vitro tests with bovine blood were conducted to collect data about the non-linear dependency of blood flow rate, flow resistance (pressure difference) and whole blood viscosity on motor current and rotation speed of a prototype blood pump. Gaussian process regression models are then used to model the non-linear mappings from motor current and rotation speed to the hydrodynamic variables of interest. The performance of the estimation is evaluated for all three variables and shows very high accuracy. For blood flow rate - correlation coefficient (r2) = 1, root mean squared error (RMSE) = 0.31 ml min-1, maximal error (ERRmax) = 9.31 ml min-1; for pressure r2 = 1, RMSE = 0.09 mmHg, ERRmax = 8.34 mmHg; and for viscosity r2 = 1,RMSE = 0.09 mPa.s, ERRmax = 0.31 mPa⋅s. The current findings suggest that this method can be employed for highly accurate online estimation of essential hydrodynamic parameters for implantable blood pumps.

In Vivo Biomechanical Assessment of a Novel Handle-Based Wheelchair Drive.

Push-rim wheelchair propulsion frequently causes severe upper limb injuries in people relying on the wheelchair for ambulation. To address this problem, we developed a novel handle-based wheelchair propulsion method that follows a cyclic motion within ergonomic joint ranges of motion. The aim of this study was to measure hand propulsion forces, joint excursions and net joint torques for this novel propulsion device and to compare its performance against traditional push-rim wheelchair propulsion. We hypothesized that under similar conditions, joint excursions of this novel handle-based device will remain within their ergonomic range and that the effectiveness of the propulsion forces will be higher, leading to lower average propulsion forces compared to push-rim propulsion and reducing the risk of injury. Eight paraplegic subjects propelled the new device at two different loads on a custom-made wheelchair-based test rig. Video motion capture and force sensors were used to monitor shoulder and wrist joint kinematics and kinetics. Shoulder and wrist loads were calculated using a modified upper-extremity Wheelchair Propulsion Model available in OpenSim. The results show that with this novel propulsion device joint excursions are within their recommended ergonomic ranges, resulting in a reduced range of motion of up to 30% at the shoulder and up to 80% at the wrist, while average resultant peak forces were reduced by up to 20% compared to push-rim propulsion. Furthermore, the lower net torques at both the shoulder and wrist demonstrate the potential of this novel propulsion system to reduce the risk of upper-extremity injuries.

Animal blood in translational research: How to adjust animal blood viscosity to the human standard.

Animal blood is used in mock circulations or in forensic bloodstain pattern analysis. Blood viscosity is important in these settings as it determines the driving pressure through biomedical devices and the shape of the bloodstain. However, animal blood can never exactly mimic human blood due to erythrocyte properties differing among species. This results in the species-specific shear thinning behavior of blood suspensions, and it is therefore not enough to adjust the hematocrit of an animal blood sample to mimic the behavior of human blood over the entire range of shear rates that are present in the body. In order to optimize experiments that require animal blood, we need models to adapt the blood samples. We here offer mathematical models derived for each species using a multi linear regression approach to describe the influence of shear rate, hematocrit, and temperature on blood viscosity. Results show that pig blood cannot be recommended for experiments at low flow conditions (<200 s-1 ) even though erythrocyte properties are similar in pigs and humans. However, pig blood mimics human blood excellently at high flow condition. Horse blood is unsuitable as experimental model in this regard. For several studied conditions, sheep blood was the closest match to human blood viscosity among the tested species.

Estimation Methods for Viscosity, Flow Rate and Pressure from Pump-Motor Assembly Parameters.

Blood pumps have found applications in heart support devices, oxygenators, and dialysis systems, among others. Often, there is no room for sensors, or the sensors are simply unreliable when long-term operation is required. However, control systems rely on those hard-to-measure parameters, such as blood flow rate and pressure difference, thus their estimation takes a central role in the development process of such medical devices. The viscosity of the blood not only influences the estimation of those parameters but is often a parameter that is of great interest to both doctors and engineers. In this work, estimation methods for blood flow rate, pressure difference, and viscosity are presented using Gaussian process regression models. Different water-glycerol mixtures were used to model blood. Data was collected from a custom-built blood pump, designed for intracorporeal oxygenators in an in vitro test circuit. The estimation was performed from motor current and motor speed measurements and its accuracy was measured for: blood flow rate r2 = 0.98, root mean squared error (RMSE) = 46 mL.min-1; pressure difference r2 = 0.98, RMSE = 8.7 mmHg; and viscosity r2 = 0.98, RMSE = 0. 0.049 mPa.s. The results suggest that the presented methods can be used to accurately predict blood flow rate, pressure, and viscosity online.

Forward dynamic optimization of handle path and muscle activity for handle based isokinetic wheelchair propulsion: A simulation study.

Push-rim wheelchair propulsion is biomechanically inefficient and physiologically stressful to the musculoskeletal structure of human body. This study focuses to obtain a new, optimized propulsion shape for wheelchair users, which is within the ergonomic ranges of joint motion, thus reducing the probability of injuries. To identify the propulsion movement, forward dynamic optimization was performed on a 3D human musculoskeletal model linked to a handle based propulsion mechanism, having shape and muscle excitations as optimization variables. The optimization resulted in a handle path shape with a circularity ratio of 0.95, and produced a net propulsion power of 34.7 watts for an isokinetic propulsion cycle at 50 rpm. Compared to push-rim propulsion, the compact design of the new propulsion mechanism along with the ergonomically optimized propulsion shape may help to reduce the risk of injuries and thus improve the quality of life for wheelchair users.

Closed-loop helium circulation system for actuation of a continuously operating heart catheter pump.

BACKGROUND: Currently available, pneumatic-based medical devices are operated using closed-loop pulsatile or open continuous systems. Medical devices utilizing gases with a low atomic number in a continuous closed loop stream have not been documented to date. This work presents the construction of a portable helium circulation addressing the need for actuating a novel, pneumatically operated catheter pump. The design of its control system puts emphasis on the performance, safety and low running cost of the catheter pump. METHODS AND RESULTS: Static and dynamic characteristics of individual elements in the circulation are analyzed to ensure a proper operation of the system. The pneumatic circulation maximizes the working range of the drive unit inside the catheter pump while reducing the total size and noise production.Separate flow and pressure controllers position the turbine's working point into the stable region of the pressure creation element. A subsystem for rapid gas evacuation significantly decreases the duration of helium removal after a leak, reaching subatmospheric pressure in the intracorporeal catheter within several milliseconds. CONCLUSIONS: The system presented in the study offers an easy control of helium mass flow while ensuring stable behavior of its internal components.

Feedback control of arm movements using Neuro-Muscular Electrical Stimulation (NMES) combined with a lockable, passive exoskeleton for gravity compensation.

Within the European project MUNDUS, an assistive framework was developed for the support of arm and hand functions during daily life activities in severely impaired people. This contribution aims at designing a feedback control system for Neuro-Muscular Electrical Stimulation (NMES) to enable reaching functions in people with no residual voluntary control of the arm and shoulder due to high level spinal cord injury. NMES is applied to the deltoids and the biceps muscles and integrated with a three degrees of freedom (DoFs) passive exoskeleton, which partially compensates gravitational forces and allows to lock each DOF. The user is able to choose the target hand position and to trigger actions using an eyetracker system. The target position is selected by using the eyetracker and determined by a marker-based tracking system using Microsoft Kinect. A central controller, i.e., a finite state machine, issues a sequence of basic movement commands to the real-time arm controller. The NMES control algorithm sequentially controls each joint angle while locking the other DoFs. Daily activities, such as drinking, brushing hair, pushing an alarm button, etc., can be supported by the system. The robust and easily tunable control approach was evaluated with five healthy subjects during a drinking task. Subjects were asked to remain passive and to allow NMES to induce the movements. In all of them, the controller was able to perform the task, and a mean hand positioning error of less than five centimeters was achieved. The average total time duration for moving the hand from a rest position to a drinking cup, for moving the cup to the mouth and back, and for finally returning the arm to the rest position was 71 s.

MUNDUS project: MUltimodal neuroprosthesis for daily upper limb support.

BACKGROUND: MUNDUS is an assistive framework for recovering direct interaction capability of severely motor impaired people based on arm reaching and hand functions. It aims at achieving personalization, modularity and maximization of the user's direct involvement in assistive systems. To this, MUNDUS exploits any residual control of the end-user and can be adapted to the level of severity or to the progression of the disease allowing the user to voluntarily interact with the environment. MUNDUS target pathologies are high-level spinal cord injury (SCI) and neurodegenerative and genetic neuromuscular diseases, such as amyotrophic lateral sclerosis, Friedreich ataxia, and multiple sclerosis (MS). The system can be alternatively driven by residual voluntary muscular activation, head/eye motion, and brain signals. MUNDUS modularly combines an antigravity lightweight and non-cumbersome exoskeleton, closed-loop controlled Neuromuscular Electrical Stimulation for arm and hand motion, and potentially a motorized hand orthosis, for grasping interactive objects. METHODS: The definition of the requirements and of the interaction tasks were designed by a focus group with experts and a questionnaire with 36 potential end-users. RESULTS: The functionality of all modules has been successfully demonstrated. User's intention was detected with a 100% success. Averaging all subjects and tasks, the minimum evaluation score obtained was 1.13 ± 0.99 for the release of the handle during the drinking task, whilst all the other sub-actions achieved a mean value above 1.6. All users, but one, subjectively perceived the usefulness of the assistance and could easily control the system. Donning time ranged from 6 to 65 minutes, scaled on the configuration complexity. CONCLUSIONS: The MUNDUS platform provides functional assistance to daily life activities; the modules integration depends on the user's need, the functionality of the system have been demonstrated for all the possible configurations, and preliminary assessment of usability and acceptance is promising.

Monitoring of spasticity and functional ability in individuals with incomplete spinal cord injury with a functional electrical stimulation cycling system.

BACKGROUND: The aim of this study was to investigate the integration of motor function and spasticity assessment of individuals with spinal cord injury into cycling therapy. METHODS: Twenty-three participants with incomplete spinal cord injury performed 18 training sessions (standard deviation (SD) 14) on an instrumented tricycle combined with functional electrical stimulation. Each therapy session included a power output test to assess the participants' ability to pedal actively and a spasticity test routine that measures the legs' resistance to the pedalling motion. In addition, the required time for the therapy phases was monitored. RESULTS: The results of the power output test showed a monthly increase in power output of 4.4 W (SD 13.7) at 30 rpm and 18.2 W (SD 23.9) at 60 rpm. The results of the spasticity assessment indicate a 12.2 W (SD 9.7) reduction in resistance at 60 rpm after the FES training for the subject group with spasticity. CONCLUSION: In clinical use over a time-period of 2 years this combined form of therapy and motor function assessment was well accepted by participants. The active power output test and the spasticity test routine offered a proper tool to monitor participants' progress in functional rehabilitation and changes in spasticity.

Consequences of ankle joint fixation on FES cycling power output: a simulation study.

INTRODUCTION: During fixed-ankle FES cycling in paraplegics, in which the leg position is completely determined by the crank angle, mechanical power output is low. This low power output limits the cardiovascular load that could be realized during FES ergometer cycling, and limits possibilities for FES cycling as a means of locomotion. Stimulation of ankle musculature in a released-ankle setup might increase power output. However, releasing the ankle joint introduces a degree of freedom in the leg that has to be controlled, which imposes constraints on the stimulation pattern. METHODS: In this study, a forward dynamics modeling/simulation approach was used to assess the potential effect of releasing the ankle on the maximal mechanical power output. RESULTS: For the released-ankle setup, the optimal stimulation pattern was found to be less tightly related to muscle shortening/lengthening than for the fixed-ankle setup, which indicates the importance of the constraints introduced by releasing the ankle. As a result, the maximal power output for 45-RPM cycling in the released-ankle setup was found to be about 10% lower than with a fixed ankle, despite the additional muscle mass available for stimulation. Power output for the released-ankle setup can be improved by tuning the point of contact between the foot and pedal to the relative strength of the ankle plantar flexors. For the model used, power output was 14% higher than for the fixed-ankle setup when this point of contact was moved posteriorly by 0.075 m. CONCLUSION: Releasing the ankle joint and stimulating the triceps surae and tibialis anterior is expected to result in a modest increase in power output at best.

Dynamic simulation of FES-cycling: influence of individual parameters.

Cycling by means of functional electrical simulation (FES) is an attractive training method for spinal cord injured (SCI) subjects. FES-cycling performance is influenced by a number of parameters like seating position, physiological parameters, conditions of surface stimulation, and pedaling rate. The objective of this paper was the determination of the influence of the most important parameters on optimal muscle stimulation patterns and power output of FES-cycling on a noncircular pedal path. The rider-cycle system was modeled as a planar articulated rigid body linkage on which the muscle forces are applied via joint moments and implemented into a forward dynamic simulation of FES-cycling. For model validation, the generated drive torques that are predicted by the simulation were compared to measurements with an individual paraplegic subject. Then, a sensitivity analysis was carried out to determine the influences of the most important parameters for surface stimulation of gluteus maximus, quadriceps, hamstrings, and peroneus reflex. The results show how optimal stimulation patterns and the expected mean active power output can be estimated based on measured individual parameters and adjusted geometry and stimulation parameters for a particular SCI-subject. This can considerably improve FES-cycling performance and relieve the patients by shortening the time that is necessary for experimental adaptation of the stimulation patterns.